DESCRIPTION
- HP & Torque: 436 HP / 443 FT LBS
Compression Ratio: 10.0:1
Aluminum Heads
Hydraulic Roller Cam
Cast Steel Crank
Hypereutectic Pistons
BLOCK:
- NEW BluePrint Cast Iron Block
Manufactured and Machined in the USA!
4-Bolt Main
4.000″ Bore
1-Piece Rear Main Seal
Mech fuel pump provision: Yes
Passenger Side Dipstick - Drilled and tapped for clutch linkage
ROTATING ASSEMBLY:
- New BluePrint Cast steel crankshaft
3.750″ Stroke
OEM type 5.700″ connecting rods w/ 150,000 psi bolts
Hypereutectic pistons
External Front/ External Rear
CYLINDER HEADS:
- BluePrint Aluminum Cylinder Heads – H8002K
64cc chamber
2.02″ intake/1.60″ exhaust valves
195cc intake/75cc exhaust runners
CAM SPECS:
- Cam Type: Roller
.544 Intake .555 Exhaust
230 Intake / 236 Exhaust duration
@ .050, 110 ° lobe separation angle
IGNITION TIMING:
- 34 Degrees Total at 3500 RPM
ALSO INCLUDES:
- Holley Sniper EFI System
Premium Vintage Valve covers
Premium Vintage Air Cleaner
6.75 inch Harmonic balancer
Spark plugs- Under Header Spark plug wires (Perfect for Rams Horn exhaust manifolds)
- Long Style Water Pump
Oil pan
Timing cover
Aluminum Intake Manifold
Small cap Ready to run distributor equipped with Tach Drive and coil
Dyno tested and shipped with results
Front Accessory Drive with Water Pump, A/C Compressor, Alternator, and Power Steering Pump (Does not fit all Corvette) See images for Dimensions
Warranty:
30 month / 50,000 mile
NOTES:
-
Not for use in pollution-controlled vehicles.
Air cleaner has a maximum height of 11.5 inches when measured from block end rail (Horizontal sealing surface under the intake manifold)
The front accessory drive on this engine fits many vehicles, however it is the customer responsibility to accurately measure and confirm fitment. Note this is a low profile design, but things such as power steering hoses, alternator wiring, and additional fittings/fabrication may be required on some vehicles.
- This engine features a true 4-inch bore, which mathematically yields 377 CID with a 3.75-inch stroke,
Warranty
The satisfaction of our customers is our highest priority at BluePrint Engines. We use quality components to balance your engine’s rotating assembly within two grams of spec. We dyno test your crate engine and certify that it’s ready to deliver horsep
Specifications
Your BluePrint engine was dyno tested with the parts and specifications listed below. If you prefer to install a different part, your engine may not produce the horsepower recorded on your dyno sheet.
Part Number: BP38318CTFKV
Fuel Delivery Type: Holley sniper EFI
Spark Plug: BPP7938 NGK 7938 BKR5E
Spark Plug Gap: .035″
Harmonic Balancer: BPP400 – 400 ci weighed, 8″ diameter
Flexplate/Flywheel: Late 350 Weighted
Stall Converter: 2000-2400 rpm
Intake Manifold: Dual plane, satin aluminum
Fuel Recommendation: 91 Octane
Timing (Initial/Total Advance): Initial timing – 10-16° and Total timing 32-34°
Firing Order: 1,8,4,3,6,5,7,2
Recommended Break in Oil : BPP710
Recommended Service Oil : BPP10W30
Recommended Oil Filter ; BPP51061
Total Oil capacity with production oil pan, and Correct BPP51061 Filter : 5 Quarts
Reviews
There are no reviews yet.